Power Running Board
No data

2. Product list

3. Installation method

1. Remove the indicated trim panels from the tailgate and hinges.

2. Remove the indicated trim panels and floor mat from the trunk.

3. Remove the left and right springs and install the right body bracket at the indicated hole.

4. Screw a countersunk screw into the indicated threaded hole.

5. Insert the M12 nut with a handle into the indicated hole.

6. Screw the M12 screw into the nut to finish the installation of the right body bracket.

7. Thread the M10 nut with a handle to the indicated position to install the left body bracket.

8. Screw the countersunk screw into the nut.

9. Insert the M12 nut with a handle into the indicated hole.

10. Screw the M12 screw into the nut to finish the installation of the left body bracket.

11. Hang the original springs at the left and right body brackets, then remove the damping rod on the left side.

12. Install the electric struts, L on the left, R on the right (the first letter of the strut code) ;the same on both sides.

13. Route the strut wiring harnesses to the right side of the trunk along with original wiring harness.

14. Remove the original latch.

15. Install the emergency cable and unfasten the unlock arm.

16. Put the cylindrical head of the cable into the reserve hole of the unlock arm and secure it at the indicated slot.

17. Install the power latch and adjust the latch to the locked state manually.

18. Connect the connectors of the lock signal harness to the power latch.

19. Connect the connectors of the lock signal harness to the original tailgate switch.

20. Hide the two emergency wires of the power latch under the trim panel of the rear right seat.

21. Route the lock signal harness to the right side of the trunk along with original wires.

22. Route the power harness to the right side of the trunk along original wires.

23. Ground at the indicated location of the left side of the trunk.

24. The fuse box is located at the right side of the trunk and the fuse for constant power is indicated above.

25. Move the original fuse from the fuse box to the fuse tap of power harness.

26. Plug the fuse tap into the fuse box and pay attention to the direction.

27. Remove the fuse box.

28. Install the ECU at the indicated hole on the right side of the trunk.

29. Secure the ECU at the indicated position.

30. Insert the left and right strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

31. Check whether the power latch and the electric struts function well.

32. Press the tailgate switch buttons to close and open the tailgate to complete the initialization, and then test each function of the electric tailgate.

33. Stick the provided hole template to the indicated position and open a hole for the added tailgate switch.

34. Reinstall all the trim panels and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key (only accessible when the vehicle is started);
●Press the original tailgate switch button;
●Press the added tailgate switch button.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.
④Switch between quick/slow press of the button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.
⑤Switch between pressing the button on remote key 2/3 times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.
Keywords:
SHOP