+
  • 18-25奥迪 Q2L (1).jpg
  • 18-25奥迪 Q2L (2).png
  • 自制大众锁.png
  • EP11撑杆.png

2018-2025Audi Q2L, Corepine Smart Electric Tailgate System Kit


Category:


Get Quote

Share to

 

2. Product List

 

3. Installation method

1. Remove the front left side trim panel, door sill panel and storage box.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the screws on the tailgate trim panel.

 

4. Remove the tailgate trim panels.

 

5. Remove the trunk floor mat.

 

6. Remove the indicated trim panel from the trunk.

 

7. Thread the lock signal harness to the left side of the trunk through the original rubber tube.(no plug connection for now)

 

8. Insert the lock signal terminals into the wiring harness connector and fasten it inward.

 

9. Remove the original latch and install our power latch.

 

10. Two plugs(A&B) are reserved. Choose one plug to connect to the original tailgate switch. After finishing the tailgate installation,test if it works. If not, choose the other plug.

 

11. Connect the plugs of the lock signal harness to the power latch.

 

12. Connect the plug of lock signal harness to the added tailgate switch.

 

13. Remove the gas struts.

 

14. Replace the body brackets on both sides of the trunk.

 

15. Install the electric struts, L on the left R on the right (the first letter of the strut code).

 

16. Drill a hole at the indicated position on both sides of the tailgate with a φ21mm drill bit.

 

17. Thread the strut wiring harnesses to the trunk as indicated; both sides are the same.

 

18.Thread the strut wiring harnesses through the rubber tubes on both sides to the trunk and route them to the left side.

 

19. Route the power harness.

 

20. Ground at the indicated position on the left side of the trunk.

 

21. Find out the CAN box behind the fuse box at the driver's position and connect to the indicated plug and its socket.

 

22. Plug the fuse tap into the indicated slot.

 

23. Secure the ECU at the indicated position.

 

24.Insert the strut wire harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

 

25. Initialize the system  and test each function of the electric tailgate.

 

26. Drill a hole at the indicated position on the right side of the tailgate trim panel with a φ14mm drill bit.

 

27. Reinstall the tailgate trim panel. Note: Slight trimming is required for any interfering parts

 

28. Reinstall all trim panels and install the added tailgate switch.

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.

④Switch between quick/slow press of the unlock button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.

⑤Switch between pressing the unlock button twice/three times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

 

Keywords:

2018-2025Audi Q2L, Corepine Smart Electric Tailgate System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW