Power Running Board
No data

2. Product List

3. Installation method

1. Remove the tailgate trim panels.

2. Remove the trunk trim panels.

3. Remove the gas strut and the spring from the left side of the trunk.

4. Remove the gas strut and the spring from the right side of the trunk.

5. Install the right body bracket. Insert the bolts with handle from the indicated position into the car body.

6. Install the right body bracket with the locating pin in the middle hole and tighten the three nuts.

7. Install the right tailgate bracket. Tighten all the nuts according to the diagram.

7-1. Model of the tailgate bracket.

8. Install the left electric strut, L on the left and R on the right (the first letter of the strut code).

9. Install the right electric strut, L on the left and R on the right (the first letter of the strut code).

10. Hang the left spring back.

11. Hang the right spring back.

12. Route the left strut wiring harness.

13. Route the right strut wiring harness to the left side.

14. Remove the plastic housing from the tailgate.

15. Connect the connectors of the lock signal harness to the original tailgate switch.

16. Remove the original latch and mount the emergency cable of the original latch onto our power latch.

17. Connect the connectors of the lock signal harness to the power latch.

18. Install the power latch. (Manually adjust the latch to the locked state to prevent accidental closing during installation)

19. Connect the connector of the lock signal harness to the added tailgate switch.

20. Route the lock signal harness to the trunk.

21. Hide the two emergency wires of the power latch under the rear left door sill panel.

22. Ground at the left side of the trunk.

23. Check all the connectors and the emergency cable.

24. Connect to the fuse box in the trunk for power supply (all the slots are constant power).
25. Plug the fuse tap into the fuse box and pay attention to the direction.

26. Install the ECU bracket at the left side of the trunk.

27. Insert the left and right strut wiring harnesses①②, lock signal harness③, and power harness④ into the ECU in sequence.

28. Check if the power latch and the struts function well.

29. Test each function of the electric tailgate.

30. Stick the hole template to the indicated position and open a hold for the installation of the added switch.

31. Reinstall all trim panels and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the tailgate button on the remote key 2 times;
●Pull up the tailgate button in the driver's area;
●Press the original tailgate switch button;
●Press the added tailgate switch button.
3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module
1.Press and hold the switch button until hearing the third short beep sound.
2.After releasing the button, you will hear three short beeps, indicating that the voice module has entered configuration mode. (For details, see the voice module operation manual)
④Block the voice module
1.Press and hold the switch button until hearing the fourth beep sound.
2.After releasing the button, you will hear four short beeps indicating that the voice module has been blocked.
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the added tailgate switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep sound and a short beep sound indicating that the switch between quick press and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑧Braking force increase (5 Settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP