Power Running Board
No data

2. Product list

3. Installation method

1. Remove the front left side trim panels and door sill panel.

2. Remove the rear left side door sill panel and B-pillar trim panel.

3. Remove the tailgate trim panels (there are screws in the circles).

4. Remove the trunk floor mat, tool box and door sill panel.

5. Remove the trim panel on the left side of the trunk.

6. Remove the handle panel from the tailgate (remove the four screw inside the tailgate first).

7. Thread the pink wire of the pair of plugs into the tailgate through the indicated hole (unwind the adhesive tape entangled on the original wiring harness).

8. Insert the pink wire into the the No. 12 slot of the wiring harness connector.

9. Connect that pair of plugs to the plugs of the original tailgate switch and then reinstall the handle panel.

10. Replace the original latch with our power latch.

11. Connect the lock signal harness to the plugs of the power latch.

12. Install the added tailgate switch.

13. Remove the gas struts.

14. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

15. Drill a hole at the indicated position with a φ21mm drill bit; both sides are the same.

16. Route the strut wiring harnesses.

17. Plug the hole tightly; both sides are the same.

18. Thread the power harness into the tailgate.

19. Route the power harness.

20. Insert the power harness terminals into the wiring harness connector as shown above.

21. Ground at the left side of the trunk.

22. Connect the power harness to the indicated signal plug and its socket.

23. The fuse slot location of constant power is indicated above (fifth in the third column).

24. Plug the fuse tap into the fuse box and pay attention to the direction of wire.

25. Remove the blank button from the switch panel and install the added front switch.

26. Fix the ECU to the indicated position.

27. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence and then mount the ECU onto its bracket.

28. Press the added tailgate switch button to open and close the tailgate once for initializing the system, and then test the functions of the electric tailgate.

29. Place the hole opener at the indicated position on the tailgate trim panel.

30. Drill a hole at the marked point with a φ14mm drill bit.

31. Install the hole opener and make sure the hole opener is parallel to the edge of the trim panel.

32. Open the hole (one wrench secures the hole opener, the other turns the nut).

33. Reinstall all trim panel and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button;
●Press the added front switch: long press for 4 seconds to open.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.
Keywords:
SHOP