+
  • 25Peugeot2008 (1).jpg
  • 25Peugeot2008 (2).jpg
  • EP11撑杆.png
  • 自制标致锁.jpg

2019-2025 Peugeot 2008,Corepine Smart Electric Tailgate System Kit


Category:


Get Quote

Share to

2. Product List

3. Installation method

1. Remove the driver side door sill panel and fuse box trim panels.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the trim panel on the left side of the trunk.

 

4. Remove the tailgate trim panels.

 

5. Remove the original gas struts.

 

6. Replace the left body bracket.

 

7. . Replace the right body bracket.

 

8. Replace the tailgate ball stud.

 

9. Install the electric struts, L on the left and R on the right (the first letter of the strut code). The end with wiring harness should be on the tailgate.

 

10. Remove the indicated trim panels.

 

11. Drill a hole at the indicated position with a Ø21 drill bit to allow strut wiring harness to pass through, the same on both sides.

 

12. Route the left and right strut wiring harnesses as shown in the diagram and seal the holes.

 

13. Remove the original latch.

 

14. Connect the connectors of the lock signal harness to the power latch.

 

15. Install the power latch.

 

16. Route the power harness to the tailgate. (routing only, no connection)

 

17. Route the power harness as shown in the diagram. (routing only, no connection)

 

18. Insert the power harness terminals into the connector as shown in the diagram(the connector is inserted on the ECU).

 

19. Locate the fuse box in the driver's area.

 

20. Plug the fuse tap into the fuse box and pay attention to the direction.

 

21. Ground at the indicated location on the tailgate.

 

22. Locate the indicated A-pillar connector.

 

23. Connect the power harness connectors to the A-pillar conector and its socket above the fuse box.

 

24. Connect the connectors of front switch harness to the original headlight adjustment switch for button light. 

 

25. Remove the blank button of the indicated position and install our front switch.

 

26. Open a φ6mm hole at the indicated position of the tailgate and install the ECU.

 

27. Insert the left and right strut wiring harnesses①②,lock signal harness③,and power harness④ into the ECU in sequence.

 

28. Press the added tailgate switch button to close the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

 

29. Stick the hole template to the indicated position  of the tailgate and open a hole. 

 

30. Install the added tailgate switch and reinstall all the trim panels.

 

4. System initialization method


1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close;
●Press the unlock button and the lock button on the remote key alternately, three times each;
●Press and hold the added front switch button for 4s to open and press once to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)

④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.

⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps —  the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)

⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.

Keywords:

2019-2025 Peugeot 2008,Corepine Smart Electric Tailgate System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW