+
  • 25Tayron (1).jpg
  • 25Tayron (2).jpg
  • 自制大众锁.png
  • EP11撑杆.png

2025 Volkswagen Tayron,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

 

2. Product List

3. Installation method

1. Remove the driver side door sill panels and fuse box trim panels.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the screws securing the tailgate trim panel.

 

4. Remove the tailgate trim panels.

 

5. Remove the original gas struts.

 

6. Take out the trunk floor mat and remove the indicated trim panels.

 

7. Replace the left body bracket.

 

8. Replace the right body bracket.

 

9. Install the electric struts, L on the left and R on the right (the first letter of the strut code). The end with wiring harness should be on the car body.

 

10. Thread the strut wiring harness through the indicated hole, the same on both sides.

 

11. Route the left and right strut wiring harnesses to the tailgate as indicated. Seal the holes with grommets.

 

 

12. Take off the original latch plastic housing. Remove the original tailgate lock.

 

 

13. Install the power latch and the original latch plastic housing.

 

14. Connect the connectors of the lock signal harness to the power latch.

 

15. Connect the connectors of the lock signal harness to the original tailgate switch.

 

16. Route the lock signal harness to the left of the trunk as indicated(do not connect plugs before inserting terminals into wire harness connector).

 

17. Route the power harness to the left of the tailgate.

 

18. Ground at the left side of the trunk.

 

19. Under the steering wheel, locate the signal connector and plug in the mating connector.

 

20. The fuse box is located at the driver’s area and the fuse slot for power supply is indicated above.

 

21. Plug the fuse tap into the fuse box and pay attention to the direction of wire.

 

22. Remove the wire clip at the indicated place, and secure the ECU with a nut.

 

23. Insert the lock signal harness terminals into the connector according to the diagram.

 

24. Insert the left and right strut wiring harnesses①②,lock signal harness③,and power harness④ into the ECU in sequence.

 

25. Press the added tailgate switch button to close the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

 

26. Remove the original blank cover, install the added tailgate switch and reinstall all the trim panels.

 

4. System initialization method


1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close;
●Press and hold the added front switch button for 4s.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module
1.Press and hold the switch button until hearing the third short beep sound. 
2.After releasing the button, you will hear three short beeps, indicating that the voice module has entered configuration mode. (For details, see the voice module operation manual)
④Block the voice module
1.Press and hold the switch button until hearing the fourth beep sound.

2.After releasing the button, you will hear four short beeps indicating that the voice module has been blocked.
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the added tailgate switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep sound and a short beep sound indicating that the switch between quick press and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.

⑧Braking force increase (5 Settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.

Keywords:

2025 Volkswagen Tayron,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW