Power Running Board
No data

2. Product list

3. Installation method

1. Remove the tailgate trim panels.

2. Remove the front right side switch panel and door sill panel.

3. Remove the rear right door sill panel.

4. Remove the front left door sill panel and the trim panel on the right side of front passenger seat.

5. Remove the right side trim panel from the trunk to allow the wiring harnesses to pass through.

6. Remove the original gas struts.

7. Replace the left body bracket.

8. Replace the right body bracket.

9. Install the bracket on the left side the of the tailgate.

10. Install the bracket on the right side the of the tailgate.

11.Install the electric struts, L on the left and R on the right (the first letter of the strut code).

12. Drill a hole at the indicated position using a φ21mm drill bit to allow the strut wiring harness to pass through. Both sides are the same.

13. Route the left and right strut wiring harnesses to the tailgate.

14. Seal the holes on both sides of the tailgate with grommets.

15. Connect the connectors of the lock signal harness to the power latch.

16. Connect the connectors of the lock signal harness to the original tailgate switch.

17. Remove the original small panel from the tailgate and install the added tailgate switch.

18. Route the power harness (routing, no plug or power connection).

19. Thread the power harness to the tailgate.

20. Insert the power harness terminals into the wiring harness connector according to the diagram.

21. Ground at the tailgate.

22. Connect the connectors of the power harness to the signal connector pair beside the pedals.

23. Remove the blank button from the switch panel and install the front tailgate switch.

24. Connect the connectors of the front switch behind the switch panel.

25. Route the fuse tap of the power harness from the rear seat to the front passenger seat.

26. The fuse box is located in front of the passenger seat and the fuse slot for power supply is indicated above.

27. Move the original fuse from the fuse box to the fuse tap, then plug the fuse tap into the fuse box.

28. Place the ECU at the indicated location of tailgate and secure it with a nut.

29. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

30. Press the added tailgate switch to open and close the tailgate once, the system completes initialization and then test each function of the electric tailgate.

31. Reinstall all the trim panels.
4. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.
⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps — the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.
5. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP