Power Running Board
No data

2. Product List

3. Installation method.
1. Remove the indicated trim panel and step board.

2. Remove the middle door step board.

3. Remove the trim panels on the left side of the trunk to allow wiring harnesses to pass through.

4. Remove the tailgate trim panels.

5. Remove the original gas struts.

6. Replace the body ball stud and place a shim between the ball stud and vehicle body; both sides are the same.

7. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the tailgate.

8. Drill a hole at the indicated position on the left side of the trunk with a φ21mm drill bit to allow the wiring harness to pass through.

9. Drill a hole at the indicated position on the right side of the trunk with a φ21mm drill bit to allow the wiring harness to pass through.

10. Route the strut wiring harnesses as indicated in the diagram.

11. Seal the the holes on both sides of the tailgate securely.

12. Remove the cover of the power latch.

13. Connect the connectors of the lock signal harness to the original tailgate switch.

14. Connect the connectors of the lock signal harness to the indicated plug of the latch and its socket.

15. Connect the lock signal harness to the connectors of the latch motor.

16. Route the power harness (Routing only, no plug or power connection).

17. Thread power harness to the tailgate.

18. Insert the power harness terminals into the wiring harness connector.

19. Ground at the left side of the pedals with the original ground wire connector.

20. Connect the power harness to the indicated signal plug and its socket under the driver's seat.

21. Check all the plugs.

22. The fuse box is located under the driver's seat and the indicated slot is used for power supply.

23. Plug the fuse tap into the fuse box and pay attention to the direction.

24. Place the ECU bracket at the indicated position and secure it with a nut.

25. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence and then mount the ECU onto its bracket.

26. Press the added tailgate switch button to open and close the tailgate once for initializing the system, and then test each function of the electric tailgate.

27. Open a hole at the indicated position for the added tailgate switch (as close as possible to the folded edge).

28. Reinstall all trim panels and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the tailgate button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.
Keywords:
SHOP
