Power Running Board
No data

2. Product List
3. Installation method

1. Remove the tailgate trim panels (there are screws in the circles).

2. Take out the trunk floor mat. Remove the screws from door sill panel and the trim panel on the left side.

3. Remove the trim panel on the left side of the trunk.

4. Remove the front left side trim panel and door sill panel.

5. Remove the rear left side door sill panel and B-pillar trim panel.

6. Remove the original latch and install our lock latch.

7. Connect the connectors of the lock signal harness to the power latch.

8.Connect the connector of the lock signal harness to the exterior handle switch.

9. Install the power latch.

10. Thread the lock signal harness to the left side of the trunk.

11. Insert the lock signal harness terminals into the wiring harness connector.

12. Remove the original gas struts.

13. Replace the left and right body brackets.

14. Install the electric struts, L on the left and R on the right (the first letter of the strut code),

15. Thread the strut wire harnesses through the holes beside the hinges into the left side of the trunk and then plug the holes securely.

16. Route the power harness.

17. Ground at the indicated location of the left side of the trunk.

18. Connect the power harness to the indicated signal plug and its socket on the CAN box behind the fuse box.

19. Plug the fuse tap into the indicated slot (fourth in the third row) with wire pointing downward.

20. Insert the strut wire harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence and then mount the ECU onto its bracket.

21. Secure the ECU at the indicated location.

22. Initialize the system once and test each function of the electric tailgate.

23. Stick the hole template to the indicated location on the tailgate trim panel.

24. Reinstall all trim panels and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press the unlock button in the driver's area 3 times;
●Press the exterior handle switch button;
●Press the added tailgate switch button.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound.
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module
1.Press and hold the switch button until hearing the third short beep sound.
2.After releasing the button, you will hear three short beeps, indicating that the voice module has entered configuration mode. (For details, see the voice module operation manual)
④Block the voice module
1.Press and hold the switch button until hearing the fourth beep sound.
2.After releasing the button, you will hear four short beeps indicating that the voice module has been blocked.
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep sound and a short beep sound indicating that the switch between quick and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑧Braking force increase (five settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
3.Repeat this step to increase by one setting.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP
