+
  • 18Troc.jpg
  • 18Troc.png
  • 自制大众锁.png
  • EP11撑杆.png

2018-2022 Volkswagen T-Roc,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product List

3. Installation method

1. Remove the front left side trim panel, door sill panel and storage box.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the indicated screws from the tailgate trim panel.

 

4. Remove the tailgate trim panels.

 

5. Take out the trunk floor mat and the trim panel on the left side.

 

6. Remove the gas struts and the bump stops.

 

7. Install the left body bracket.

 

8. Install the right body bracket.

 

9. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the tailgate.

 

10. Remove the left and right bump stops and pass the strut wiring harnesses into the tailgate through the holes.

 

11. Route the strut wiring harnesses to the left side of the trunk as indicated in the diagram and plug the holes.

 

12. Remove the original latch.

 

13. Connect the connectors of the lock signal harness to the power latch .

 

14. Connect the connectors of the lock signal harness to the original tailgate switch. (If there is electricity running through the pink wire, the correct connector pair has been connected).

 

 

15. Install the power latch.

 

16. Route the lock signal harness to the left side of the trunk. (routing only, no connection)

 

17. Insert the lock signal harness terminals to the connector as indicated above.

 

18. Route the power harness as indicated above along the original wiring harness.

 

19. Ground at the indicated location.

 

20. Remove the gear shift boot first and remove the air conditioner panel.

 

21. Connect to the indicated plug and its socket behind the air conditioner panel for CAN signal.

 

22. Plug the fuse tap into the indicated location (the seventh slot in the fourth row).

 

23. Insert the left and right strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

 

24. Remove the red tube clip.

 

25. Secure the ECU and its bracket at that hole.

 

26. Press the added tailgate switch button to close the tailgate and test each function of the electric tailgate.

 

27. Reinstall all trim panels and install the added tailgate switch (remove the original small panel).

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press the unlock button on the remote key 3 times; 
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.

④Switch between quick/slow press of the unlock button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.

⑤Switch between pressing the unlock button twice/three times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

Keywords:

2018-2022 Volkswagen T-Roc,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW