+
  • 23Tharu.jpg
  • 23Tharu.png
  • 自制大众锁.png
  • EP11撑杆.png

2023 Volkswagen Tharu,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

 

2. Product List

 

3. Installation method

1. Remove front left door sill panels, switch panel and steering column panel.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the indicated panel from trunk.

 

4. Remove the screws of handle.

 

5. Remove the trim panels from tailgate.

 

6. Remove the original gas struts.

 

7. Replace the bracket on the left side of the trunk.

 

8. Replace the bracket on the left side of the trunk.

 

9. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the vehicle body.

 

10. Thread the strut wiring harness through the indicated hole into the trunk.

 

11. Route the left and right strut wiring harnesses to the left side of the trunk.

 

12. Seal the holes with grommets.

 

13. Route the lock signal harness to the left side of trunk along  the original wiring harness.

 

14. Insert the lock signal harness terminals into the connector on ECU.

 

15. Remove the original latch.

 

16. Connect the connectors of lock signal harness to the power latch.

 

17. Install the power latch and cover the latch with original latch casing.

 

18. Connect the connectors of lock signal harness to original tailgate switch.

 

19. Route the power harness.

 

20. Ground at the indicated location on the left side of the trunk.

 

21. Connect the lock signal harness to CAN signal connectors inside the steering column panel.

 

22. Check if all the plugs are connected properly.

 

23. The fuse slot for power supply is indicated above.

 

24. Plug the fuse tap into the fuse box. Pay attention to the direction.

 

25. Secure ECU at the indicated position.

 

26. Insert the left and right strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

 

27. Press the added tailgate switch button to open and close the tailgate once for initializing the system, and then test each function of the electric tailgate.

 

28. Stick the hole template to the indicated position and open a hole for installing the added tailgate switch.

 

29. Install the added tailgate switch and reinstall all trim panels.

 

5. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

6. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Long press the tailgate button on the remote key;
●Press the unlock button in the driver's area 3 times;
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.

④Switch between quick/slow press of the unlock button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.

⑤Switch between pressing the unlock button twice/three times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.

 

7. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

 

Keywords:

2023 Volkswagen Tharu,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW