Power Running Board
No data

2. Product List

3. Installation method

1. Remove the indicated driver’s side trim panels.

2. Remove the rear left door sill panel and B-pillar trim panel.

3. Remove the screws from the tailgate trim panels.

4. Remove the tailgate trim panels.

5. Take out the trunk floor mat and remove the lower trunk trim panel.

6. Remove the trim panel on the left side of the trunk.

7. Remove the original latch and install the power latch.

8. Route the lock signal harness to the left side of the trunk (do not connect plugs before inserting terminals into connector).

9. Insert the lock signal harness terminals into the connector according to the diagram.

10. Connect the connectors of the lock signal harness to the power latch.

11. Connect the connectors of the lock signal harness to the original tailgate switch.

12. Connect the connector of the lock signal harness to the added tailgate switch.

13. Remove the gas struts.

14. Replace the left body bracket (use original screws).

15. Replace the right body bracket (use original screws).

16. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

17. Remove the rubber plug beside the hinge and route the strut wiring harness to the left side of the trunk.

18. Seal the hole plugs on both sides.

19. Route the power harness as indicated.

20. Ground at the indicated position on the left side of the trunk.

21. Find out the CAN box behind the storage box and connect to the indicated plug and its socket.

22. Plug the fuse tap into the indicated slot (seventh in the fourth row).

23. Drill a hole at the indicated position with a φ6 drill bit for installing the ECU bracket.

24. Insert the left and right strut wiring harnesses①②, lock signal harness③, and power harness④ into the ECU in sequence.

25. Press the added tailgate switch to close the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

26. Install the added tailgate switch and reinstall all the trim panels.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press and hold the unlock button on the remote key;
●Press the unlock button in the driver's area 3 times;
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound.
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module
1.Press and hold the switch button until hearing the third short beep sound.
2.After releasing the button, you will hear three short beeps, indicating that the voice module has entered configuration mode. (For details, see the voice module operation manual)
④Block the voice module
1.Press and hold the switch button until hearing the fourth beep sound.
2.After releasing the button, you will hear four short beeps indicating that the voice module has been blocked.
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep sound and a short beep sound indicating that the switch between quick and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑧Braking force increase (five settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
3.Repeat this step to increase by one setting.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP