Power Running Board
No data
2019-2023 Volkswagen Sagitar,Corepine Smart Power Automatic Car Electric Tailgate Lift System Kit Strut New Condition Body Parts for
Get Quote

2. Product List

3. Installation method

1. Remove the front left side door sill panel and the trim panels of the fuse box.

2. Remove the rear left door sill panel and B-pillar trim panel.

3. Fold the rear seats.

4. Take out the trunk floor mat and the indicated trim panels.

5. Remove the tailgate trim panels.

6. Install the left and right body brackets at the indicated locations.

7. Install the left body bracket: insert the M6 bolt with handle into the location① and pass it through to the indicated location②.

8. Secure the left body bracket at the indicated location first and insert the M10 bolt into the location① and pass it through to the indicated location.

9. Insert the nut with handle into the indicated location and screw the nut onto the indicated bolt.

10. Install the right body bracket in the same way.

11. Remove the original cable clip and gas strut.

12. Install the left tailgate bracket on the hinge, insert the locating pin into the hole of cable clip and secure the hex head bolts and eye bolts as indicated.

13. Fit the locating hole of the bracket onto the spring hook and install the hex socket bolts and eye bolts as indicated.

14. Tighten the nuts on those bolts.

15. Remove the original latch.

16. Connect the connectors of the lock signal harness to the power latch.

17. Install the power latch and put the original plastic casing on the power latch.

18. Connect the connectors of the lock signal harness to the original tailgate switch.

19. Route the lock signal harness to the left side of the trunk.

20. Tie the lock signal harness to the hinge as indicated and leave sufficient allowance in length.

21. Route the power harness.

22. Ground at the left side of the driver's area.

23. The fuse box is located in the driver's area and the fuse slot for power supply is indicated above.

24. Plug the fuse tap into the fuse box and pay attention to the direction of wire.

25. Open a hole at the indicated location to expose the ball stud of the body bracket and thread the strut wiring harness through the hole.

26. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

27. Route the strut wiring harnesses to the left side of the trunk.

28. Secure the ECU at the indicated location with a nut.

29. Insert the left and right strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

30. Check whether the power latch and the electric struts function well.

31. Press the original tailgate switch button to open the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

32. Stick the hole template to the indicated location and open a hole for the added tailgate switch.

33. Install the added tailgate switch and reinstall all trim panels.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press the tailgate button at the driver's area;
●Press the original tailgate switch button;
●Press the added tailgate switch button.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound.
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module (see the voice module operation manual)
④Block the voice module (see the voice module operation manual)
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep and a short beep indicating that the switch between quick and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑧Braking force increase (five settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
3.Repeat this step to increase by one setting.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP