+
  • 19Tharu.png
  • 19Tharu.jpg
  • 自制大众锁.png
  • EP11撑杆.png

2019-2022 Volkswagen Tharu,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

 

2. Product List

 

3. Installation method

1. Remove the indicated driver’s side trim panels.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the screws from the tailgate handle.

 

4. Remove the tailgate trim panels.

 

5. Take out the trunk floor mat and remove the lower trim panel.

 

6. Remove the trim panel on the left side of the trunk.

 

7. Remove the original latch and install our power latch.

 

8. Connect the connectors of the lock signal harness to the power latch.

 

9. Connect the connectors of the lock signal harness to the original tailgate switch.

 

10. Remove the original gas struts.

 

11. Replace the ball studs on both sides of the tailgate.

 

12. Replace the left body bracket and make sure the ball stud is positioned closer to the inner side.

 

13. Replace the right body bracket and make sure the ball stud is positioned closer to the inner side.

 

14. Drill a hole at the indicated position with a 14mm drill bit.

 

15. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

 

16. Thread the strut wiring harness into the tailgate and plug the hole.

 

17. Thread the power harness to the tailgate.

 

18. Insert the power harness terminals into the connector according to the diagram.

 

19. Route the power harness as indicated.

 

20. Ground at the indicated position.

 

21. Find out the CAN box behind the fuse box and connect to the indicated plug and its socket.

 

22. Plug the fuse tap into the indicated slot and pay attention to the direction.

 

23. Drill a hole at the indicated position with a 6mm drill bit.

 

24. Secure the ECU bracket at the hole with a nut.

 

25. Insert the left and right strut wiring harnesses①②, lock signal harness③, and power harness④ into the ECU in sequence.

 

26. Press the added tailgate switch to close the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

 

27. Stick the hold template to the indicated position and drill a hole.

 

28. Install the added tailgate switch and reinstall all the trim panels.

 

(Optional) Drill drill a φ21mm hole with provided hole saw and fit the front switch in.

 

Insert the two terminals of the front switch extension wire into power harness connector according to the wire label.

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically.
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press the unlock button in the driver's position 3 times;
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.

④Switch between quick/slow press of the unlock button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.

⑤Switch between pressing the unlock button twice/three times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

 

 

Keywords:

2019-2022 Volkswagen Tharu,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW