+
  • 12LandCruiser (1).png
  • 12LandCruiser (2).png
  • 自制丰田锁.jpg
  • EP11撑杆.png

2011-2015 Toyota Land Cruiser,Corepine Smart Electric Tailgate System Kit


Category:


Get Quote

Share to

 

2. Product list

 

3. Installation method

1. Install the corresponding reinforcing washers to the hinges with provided screws according to different vehicle models.

 

2. Remove the front left side trim panels, door sill panel and storage box.

 

3. Remove the rear left door sill panel and B-pillar trim panel.

 

4. Remove the tailgate trim panels (there are screws in the circles).

 

5. Remove the trim panels on the left side of the trunk.

 

6. Remove the original latch.

 

7. Connect the connectors of the lock signal harness to the original tailgate switch.

 

8. Remove the screws from the power latch.

 

9. Install the power latch.

 

10. Connect the connectors of the lock signal harness to the power latch.

 

11. Connect the connector of the lock signal harness to the added tailgate switch.

 

12. Remove the gas struts.

 

13. Replace the left and right body ball studs.

 

14. Replace the left and right tailgate brackets (the ball studs are on the top half and near the spoiler).

 

15. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

 

16. Remove left and right tailgate rubber pads.

 

17. Open a hole at the indicated location of the rubber pads (as long as the plugs of strut wiring harness can fit through).

 

18. Remove the screw from the hole and pass the strut wiring harness through the hole.

 

19. Route the strut wiring harnesses as indicated.

 

20. Reinstall the screw and seal the hole securely. Same on both sides.

 

21. Route the power harness to the left side of tailgate (no connection before inserting terminals into wiring harness connector).

 

22. Insert the power harness terminals into the wiring harness connector according to the diagram.

 

23. Route the power harness.

 

24. Ground at the indicated location.

 

25. Remove the blank button from the switch panel and install the added front switch.

 

26. Connect the connectors of power harness to the B-pillar signal connectors.

 

27. Move the indicated fuse (sixth in the rightmost column),  to the fuse tap and then plug the fuse tap into the fuse box.

 

28. Insert the strut wiring harnesses ①②,  lock signal harness ③, and power harness④ into the ECU in sequence, and mount the ECU on its bracket.

 

29. Screw a nut on the ECU bracket first and then secure it at the indicated hole.

 

30. Initialize the system once, and then test the functions of the electric tailgate.

 

31. Drill a hole at the right part of the tailgate using a φ14mm drill bit.

 

32. Install the hole opener (make sure its edge is parallel to the lower edge of the tailgate) and open the hole (one wrench holds the hole opener and the other wrench turns the nut).

 

33. Reinstall all the trim panels and install the added tailgate switch.

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep";
3. The system initialization is complete.

 

5. Instructions for the electric tailgate

1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button;
●Press the added front switch button: press and hold for 4s to open and
  press once to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after  hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

 

Keywords:

2011-2015 Toyota Land Cruiser,Corepine Smart Electric Tailgate System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW