+
  • 17Noah80 (1).png
  • 17Noah80 (2).png
  • 自制丰田锁.jpg
  • EP11撑杆.png

2017 Toyota Noah 80(RHD),Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product list

3. Installation method

1.  Remove the tailgate trim panels.

 

2. Remove the front right side door sill panel and switch panel.

 

3. Remove the rear right side door sill panel.

 

4. Remove the front left side trim panel and door sill panel.

 

5. Remove the trim panel on the left side of the trunk to allow wiring harnesses to pass through.

 

6. Remove the original gas struts.

 

7. Install the brackets on both sides of the trunk and pay attention to the position of the ball stud.

 

8. Remove the left and right ball studs.

 

9. Drill a hole at the left side of the tailgate and for the left tailgate bracket.

 

10. Install the bracket at the left side of the tailgate and fasten the other end of the bracket with a nut.

 

11. Drill a hole at the right side of the tailgate and install the left tailgate bracket.

 

12. Install the bracket at the right side of the tailgate and fasten the other end of the bracket with a nut.

 

13. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harness are on the tailgate.

 

14. Use a 21mm drill bit to drill a hole at the indicated position of the tailgate to allow the strut wiring harness to pass through. Both sides are the same.

 

15. Thread the left and right strut wiring harnesses into the tailgate.

 

16. Seal the holes on the left and right sides of the tailgate with grommets.

 

17. Remove the original latch and try to install our power latch. If there is any interference, grind off the lower edge of the hole.

 

18. Install our power latch.

 

19. Connect the plugs of the lock signal harness to the plugs of the power latch.

 

20. Connect the plugs of the lock signal harness to the plugs of the original tailgate switch.

 

21. Remove the original small panel from the tailgate and install the added tailgate switch.

 

22. Route the power harness as indicated.

 

23. Thread the power harness to the tailgate.

 

24. Insert the power harness terminals into the wiring harness connector according to the diagram.

 

25. Ground at the original ground wire connector.

 

26. Route the plugs of the front switch wiring harness and the signal plugs to the driver's position.

 

27. Remove the blank button from the switch panel and install the added front switch.

 

28. Connect the plugs for backlight behind the switch panel.

 

29. Connect the signal plugs of the power harness to the indicated plug and its socket beside the pedals.

 

30. The fuse box is located in front of the passenger seat and the fuse slot for power supply is indicated above.

 

31. Secure the ECU at the indicated hole on the right side of the tailgate.

 

32. Insert the strut wiring harnesses ①②,  lock signal harness ③, and power harness④ into the ECU in sequence, and mount the ECU on its bracket.

 

33. Press the added tailgate switch to open and close the tailgate once for initializing the system, and then test each function of the electric tailgate.

 

34. Reinstall all the trim panels.

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button to close;
●Press the added front switch button: press and hold for 4s to open and
  press once to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after  hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

Keywords:

2017 Toyota Noah 80(RHD),Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW