+
  • 23Hiace300LowR (1).png
  • 23Hiace300LowR (2).png
  • 自制海狮锁.png
  • EP11撑杆.png

2023-2025 Toyota Hiace 300 Low Roof,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product list

3. Installation method

1. Remove the front left side trim panels and switch panel.

 

2. Remove the tailgate trim panels.

 

3. Remove the indicated trim panel to allow wiring harnesses to pass through.

 

4. Remove the original gas struts.

 

5. Replace the left body bracket.

 

6. Replace the right body bracket.

 

7. Replace the left tailgate bracket.

 

8. Replace the right tailgate bracket.

 

9. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the tailgate.

 

10. Thread the strut wiring harness through the indicated car hole; the same on both sides.

 

11. Route the left and right strut wiring harnesses to the tailgate.

 

12. Remove the original latch.

 

13. Connect the lock signal harness to the plugs of the power latch.

 

14. Install the original lock cable onto the power latch.

 

15. Stretch the original lock cable in the direction indicated above for easy installation of the power latch.

 

16. Route the power harness through the roof (routing only, no plug or power connection).

 

17. Thread  the power harness to the tailgate (routing only, no plug or power connection).

 

18. Insert the power harness terminals into the wiring harness connector according to the diagram.

 

19. Ground at the left side of tailgate.

 

20. Connect the plug of the power harness to the signal plugs at the tailgate.

 

21. Remove the blank button from the switch panel and install the added front switch.

 

22. Connect to the plugs of the switch beside the front switch for backlight.

 

23. Check if all the plugs are properly connected.

 

24. The fuse box is located beside the pedals and the fuse slot for power supply is indicated above.

 

25. Plug the fuse tap into the fuse box, and pay attention to the direction of wire.

 

26. Place the ECU at the indicated position and secure it with a nut.

 

27. Insert the strut wiring harnesses ①②,  lock signal harness ③, and power harness④ into the ECU in sequence.

 

28. Press the added tailgate switch to open and close the tailgate once, the system completes initialization, and then test the functions of the electric tailgate.

 

29. Stick the hole template to the indicated position of the tailgate and open a hole for installing the tailgate switch.

 

30. Drill a hole at the shown position of the tailgate using a φ14mm drill bit.

 

31. Install the hole opener.

 

32. Use the wrenches to open the hole.

 

33. Reinstall all the trim panels and fit the added tailgate switch in.

 

4. System initialization method


1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button to close;
●Press the added front switch button: press and hold to open and
  press once to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.

⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps —  the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)

⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.

Keywords:

2023-2025 Toyota Hiace 300 Low Roof,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW