+
  • 20Hiace300high (1).png
  • 20Hiace300high (2).png
  • 自制海狮锁.png
  • EP11撑杆.png

2020-2025 Toyota Hiace 300 High Roof ,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product list

3. Installation method

1. Remove the driver side door sill panels and fuse box trim panels.

 

2. Remove the trim panel on the left side of the roof.

 

3. Remove the tailgate trim panel.

 

4. Remove the tailgate struts.

 

5. Replace the left and right body brackets.

 

6. Replace the left tailgate bracket.

 

7. Replace the right tailgate bracket.

 

8. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

 

9. Drill a hole at the indicated location to allow the strut wiring harness to pass through. Both sides are the same.

 

10. Route the strut wiring harnesses to the tailgate as indicated.

 

11. Plug the holes on both sides.

 

12. Remove the original tailgate latch.

 

13. Connect the connectors of the lock signal harness to the power latch.

 

14. Install the lock cable.

 

15. Adjust the position of the green tape first, then adjust the lock cable to allow the lock to fit into its position.

 

16. Install the power latch.

 

17. Route the power harness (routing only, no plug or power connection).

 

18. Insert the power harness terminals into the wiring harness connector as shown above.

 

19. Ground at the indicated location on the right side of the tailgate.

 

20. Connect the connectors of the power harness to the signal connector pair of the tailgate latch.

 

21. Install the added front switch at the indicated position.

 

22. Connect the connectors of power harness to the front switch and the connectors of the switch beside it for backlight.

 

23. Check all the connectors.

 

24. The fuse box is located at the driver's area and the fuse slot for power supply is indicated above.

 

25. Plug the fuse tap into the slot and pay attention to the direction.

 

26. Insert the strut wiring harnesses ①②,  lock signal harness ③, and power harness④ into the ECU in sequence.

 

27. Secure the ECU at the indicated hole on the left side of the tailgate with a nut.

 

28. Press the tailgate switch buttons to open and close the tailgate once, the system completes initialization, and then test the functions of the electric tailgate.

 

29. Drill a hole at the indicated position with a Φ14mm drill bit.

 

30. Install the hole opener and turn the nut to open the hole.

 

31. Reinstall all the trim panels and fit the added tailgate switch in.

 

4. System initialization method


1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the added front switch button: press and hold for 4s to open and press once to close;
●Press the original tailgate switch button;
●Press the added tailgate switch button to close.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.

⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps —  the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)

⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.

 

Keywords:

2020-2025 Toyota Hiace 300 High Roof ,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW