Power Running Board
No data

2. Product list

3. Installation method

1. Remove the indicated driver side trim panel, door sill panel and switch panel.

2. Remove the rear right B-pillar trim panel and door sill panel.

3. Remove the tailgate trim panels.

4. Separate the trim panel from the right side of the trunk.

5. Remove the indicated rubber pad to allow the strut wiring harness to pass through. Same on both sides.

6. Add a washer to the hinges on both sides of the tailgate and secure them with provided screws.

7. Seal the holes on both sides with the provided rubber plugs.

8. Remove the original gas struts.

9. Install the bracket on the left side of the vehicle body.

10. Install the bracket on the right side of the vehicle body.

11. Install the bracket on the left side of the tailgate.

12. Install the bracket on the right side of the tailgate.

13. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the tailgate.

14. Pass the strut wiring harnesses through the original car holes and route them to the tailgate.

15. Insert the strut wiring harness terminals into the wiring harness connector as shown above.

16. Remove the original latch and install the power latch.

17. Connect the connectors of lock signal harness to the power latch.

18.Connect the tailgate switch signal: connect the connectors of the lock signal harness to the original tailgate switch.

19. Route the power harness along the right side of the vehicle.

20. Route the power harness to the tailgate (no connection before inserting terminals into wiring harness connector).

21. Insert the power harness terminals into the wiring harness connector as shown above.

22. Ground at the right side of trunk.

23. Connect B-pillar signal at the rear right side B-pillar.

24. Route the switch wiring harness to the driver’s area.

25. Remove the blank button from the switch panel, install the added front switch and connect to the connectors of the switch beside it for backlight.

26. The fuse box is on the right side of the front passenger seat and the fuse slot for power supply is indicated in the diagram.

27. Move the original fuse from the fuse box to the fuse tap and plug the fuse tap into the fuse box with wire pointing to the right.

28. Place the ECU at the indicated location and secure it with a nut.

29. Insert the left and right strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

30. Press the tailgate switch buttons to open and close the tailgate once, the system completes initialization, then test each function of the electric tailgate.

31. Reinstall all the trim panels and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button in the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button;
●Press the added front switch button: press and hold for 4s to open and
press once to close.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.
⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps — the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP