Power Running Board
No data

2. Product List

3. Installation method

1. Remove the front left side trim panel, door sill panel and the storage box.

2. Remove the rear left side door sill panel and B-pillar trim panel.

3. Remove the tailgate trim panels.

4. Remove the original gas struts.

5. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the tailgate.

6. Mark the positions to be drilled with tape and pay attention to avoid the taillights.

7. The final effect is as shown above.

8. Thread the left and right strut wiring harnesses into the tailgate through the drilled holes.

9. Plug the holes on both sides with the rubber plugs.

10. Remove the original latch.

11. Assemble the lock latch and actuator.

12. Install the lock latch and actuator.

13. Connect the lock signal harness to the plugs of the lock latch and the actuator.

14. Connect the lock signal harness to the plugs of the original tailgate switch and the added switch.

15. Route the power harness (wiring only, no plug or power connection).

16. Route power harness to tailgate.

17. Insert the power harness terminals into the wiring harness connector.

18. Ground at the indicated position on the tailgate.

19. Find out the indicated CAN box and connect the power harness with the CAN box and the signal plug.

20. The fuse slot for power supply is indicated above.

21. Plug the fuse tap into the fuse box.

22. Put a bolt on the ECU bracket.

23. Place the ECU at the indicated position and secure it with a nut.

24. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

25. Press the added tailgate switch to open and close the tailgate once for initializing the system, and then test the functions of the electric tailgate.

26. Drill a hole at the indicated position of the tailgate trim panel with a φ14mm drill bit.

27. Reinstall all trim panels and install the added tailgate switch.

28. Press the added tailgate switch to open and close the tailgate once for initializing the system, and then test the functions of the electric tailgate.

29. Stick the hole template the indicated position on the tailgate trim panel and open a hole for the added switch.

30. Reinstall all trim panels and install the added tailgate switch.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Long press the tailgate button on the remote key;
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area: press 3 times to close
and 6 times to open;
●Press the original tailgate switch button;
●Press the added tailgate switch button.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.
④Switch between quick/slow press of the unlock button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.
⑤Switch between pressing the unlock button twice/three times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.
Keywords:
SHOP