2. Product List
3. Installation method
1. Remove the front left side trim panels and door sill panel.

2. Remove the rear left side door sill panel and B-pillar trim panel.

3. Remove the tailgate trim panels.

4. Remove the screws from left side trim panel of the trunk as shown above.

5. Remove the trim panel on the left side of the trunk.

6. Remove the original latch.

7. Install the power latch with original screws.

8. Connect the connectors of the lock signal harness to the power latch.

9. Connect the connectors of the lock signal harness to the original tailgate switch.

10. Route the lock signal harness to the trunk. (routing only, no wire insertion for now)

11. Insert the terminals of the lock signal harness into the connector (wire quantity subject to actual).

12. Remove the gas struts.

13. Install the provided ball stud.

14. Replace the left and right body brackets. (Use the original screws for the upper end and use the provided screws for the lower end)

15. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

16. Route the strut wiring harnesses.

17. Route the power harness.

18. Connect the power harness to the indicated signal plug behind the fuse box.

19. Ground at the left side of the trunk.

20. Plug the fuse tap into the indicated slot (seventh in the fourth row).

21. Install the ECU at the indicated position.

22. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence and mount the ECU onto its bracket.

23. Initialize the system once and test each function of the electric tailgate.

24. Place the hole opener at the right side of the tailgate trim panel.

25. Place the base of the hole opener at the indicated position and mark the central point.

26. Drill a hole at the marked position with a φ14mm drill bit.

27. Install the hole opener and make it parallel to the edge of the trim panel

28. Open the hole (one hand holds the hole opener ,the other turns the nut).

29. Reinstall all trim panels and fit the added tailgate switch in.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press the unlock button in the driver's area 3 to 4 times;
●Press the unlock button on the remote key 3 times;
●Press the tailgate handle switch button;
●Press the added tailgate switch button.
3. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.
⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps — the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.