+
  • 16SkdSuperb (1).jpg
  • 16SkdSuperb (2).jpg
  • 自制大众锁.png
  • EP11撑杆.png

2016-2023 Skoda Superb,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product List

3. Installation method

1. Remove the front left side trim panel, door sill panel and storage box.

 

2. Remove the rear left side door sill panel and B-pillar trim panel.

 

3. Remove the tailgate trim panels.

 

4. Take out the trunk floor mat and remove the indicated trim panels from the trunk.

 

5. Remove the original latch and install our power latch.

 

6. Put the plastic casing on the latch part and connect the connectors of the lock signal harness to the power latch.

 

7. Install the power latch.

 

8. Remove the original gas struts.

 

9. Replace the ball studs on both sides.

 

10. Remove the rubber plug and ball stud from the tailgate.

 

11. Install the provided ball stud and washer.

 

12. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

 

13. Thread the strut wiring harnesses into the tailgate and route them as indicated above.

 

14. Thread the power harness into the tailgate and route it as indicated above.

 

15. Insert the power harness terminals into the connector.

 

16. Route the power harness.

 

17. The CAN signal plug is located behind the steering column.

 

18. Find out the indicated plug and connect the power harness to it and its socket.

 

19. Ground at the left side of the trunk.

 

20. The fuse slot for power supply is indicated above (seventh in the fourth row).

 

21. Plug the fuse tap into the fuse box and pay attention to the direction.

 

22. Locate the mounting hole of ECU.

 

23. Install the ECU bracket.

 

24. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

 

25. Initialize the system and test each function of the electric tailgate.

 

26. Open a hole at the indicatedposition with a φ21mm drill bit for the added tailgate switch.

 

27. Install the added tailgate switch and reinstall all trim panel.

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

17. The CAN signal plug is located behind the steering column.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●When the front left door is open, press the unlock button on the door
  3 times;
●When the front left door is closed, press the unlock button on the door
  6 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after  hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

 

Keywords:

2016-2023 Skoda Superb,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW