Power Running Board
No data
2. Product list

3. Installation method

1. Remove the trim panels of the tailgate and trunk.

2. Remove the the panel on the right side of the driver seat and lift the floor mat to find out the fuse box.

3. Remove the rear right door sill panel to allow the power harness to pass through.

4. Remove the original gas strut.

5. Install the left body bracket, making sure the arc edge faces outward.

6. Install the right body bracket, making sure the arc edge faces outward.

7. Replace the ball studs on both sides with provided ones.

8. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

9. Remove the right taillight to avoid damage when drilling hole.

10. Stick a marked sticker to the indicated position, then use a Φ21mm drill bit to drill a hole.

11. Install the taillight back after drilling the hole.

12. Thread the right strut wiring harness into the tailgate through the drilled hole.

13. Route the left and right strut wiring harnesses to the indicated position for convenient connection to the ECU.

14. Remove the original latch.

15. Connect the connectors of the lock signal harness to the power latch.

16. Install the power latch and secure it with the original screws.

17.Find out the plug of tthe original tailgate switch button and unplug it.

18. Connect the plugs of the lock signal harness to the original tailgate switch and its plug.

19. Route the power harness along the original wiring harnesses.

20. Route the power harness to the tailgate (routing only, no connection).

21. Insert the power harness terminals into the wiring harness connector as shown above.

22. Ground at the indicated position of tailgate by original ground wire connector.

23. Connect the signal connectors of the power harness to the indicated signal plug and its socket.

24. Connect the ring terminal to the fuse box beside the front right door for power suply and fasten with a nut.

25. Put a bolt on the bracket and then mount the ECU onto the bracket.

26. Place the ECU at the indicated hole with its sockets facing out and secure it with a nut.

27. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

28. Press the added tailgate switch to close the tailgate, and open it to complete the system initialization. Then test each function of the electric tailgate.

29. Reinstall all the trim panels and install the added switch in (Check if the added switch can bounce back normally when pressed. If there is any interference, use a small knife to scrape off the interfering part of the trim panel).

(Optional) Drill drill a φ21mm hole with provided hole saw and fit the front switch in.

Insert the two terminals of the front switch extension wire into the power harness connector according to the wire label.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button at the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button;
●Press the added front switch button: press and hold for 4s to open and
press once to close.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.
Keywords:
SHOP
