Power Running Board
No data

2. Product list

3. Installation method

1. Remove the trim panels on the tailgate and trunk.

2. Remove the springs on both sides of the trunk.

3. Remove the spring hanger from the right hinge.

4. Install the left body bracket.

5.Install the right body bracket.

6. Install the right tailgate bracket.

7. Install the left electric strut, L on the left and R on the right (the first letter of the strut code), making sure the end with wiring harness points outward.

8. Install the right electric strut, L on the left and R on the right (the first letter of the strut code), making sure the end with wiring harness points outward.

9. Hang the left spring back.

10. Hang the right spring back with one end hanging at the hole of the bracket.

11. Route the left strut wiring harness to the tailgate and tie it along with original wiring harness.

12. Wire the right strut wiring harness to the tailgate and tie it along with original wiring harness.

13. Remove the original lock and lock cable.

14. Mount the provided cable onto the power latch first.

15. Install the power latch and secure it with original screws. Manually adjust the latch to the locked state to prevent accidental closing during the installation process.

16. Mount the emergency cable onto the power latch (use mechanical key to ensure it can be unlocked).

17.Connect the plugs of lock signal harness to the plugs of the power latch.

18. Connect the plugs of lock signal harness to the plugs of original tailgate switch and the added tailgate switch.

19. Route the emergency wires of the lock signal harness along the right hinge to the right side of rear seat and hide (the emergency wires should be in place for emergency use).

20. Ground at the right side of the trunk.

21. Connect the plugs of power harness to the signal plug and its socket behind the fuse box.

22. The fuse box is located at the right side of the trunk and the fuse slot for power supply is shown above.

23. Plug the fuse tap into the fuse box and pay attention to the direction (the second slot).

24. Route the power harness to the tailgate and tie it along with the origianal wiring harnesses.

25. Put a bolt on the ECU bracket and then mount the ECU on its bracket.

26. Place the ECU at the indicated hole and secure it with a nut.

27. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

28. Manually close the tailgate until it touches the striker, then press the original tailgate switch button to open the tailgate. The system will complete initialization, and then test the functions of the electric tailgate.

29. Open a hole at the indicated position for installing the added switch.

30.Fasten the trim panel to be pierced, align it with the hole of the sheet metal, and mark the hole position with a pen.

31. Mark it.

32. Stick the hole template to the marked position.

33. Open the hole.

34. Install the added switch and check whether it can bounce back normally, and then reinstall all trim panels.
4. System initialization method
1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the tailgate button at the driver's area;
●Press and hold the tailgate button on the remote key;
●Press the original tailgate switch button to open;
●Press the added tailgate switch button to close.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.
Keywords:
SHOP