+
  • 17BenZGLC (1).png
  • 17BenZGLC (2).png
  • 奔驰B级锁.png
  • EP11撑杆.png

2017-2019 Benz GLC,Corepine Smart Electric Tailgate System Kit


Category:


Get Quote

Share to

 

2. Product list

 

3. Installation method

1. Remove the indicated parts of the trunk liner.

 

2. Remove the tailgate trim panels.

 

3. Remove the gas struts.

 

4. Replace the left and right body brackets.

 

5. Replace the left and right ball studs with our reinforcing ball studs.

 

6. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

 

7. Thread the strut wiring harnesses through the holes for bump stops on the left and right sides of the tailgate.

 

8. Route the left and right strut wiring harnesses to the right side of the tailgate.

 

9. Plug the holes on the left and right sides of the tailgate.

 

10. Insert the strut wiring harness terminals into the wiring harness connector (both sides follow the same method).

 

11. Remove the original latch and install our power latch.

 

12. Connect the connectors of the lock signal harness to the power latch as shown above.

 

13. Connect the connector of the lock signal harness to the added tailgate switch.

 

14. Connect the connectors of  the lock signal harness to the original tailgate switch.

 

15. Route the power harness to the right side of the tailgate.

 

16. Insert the power harness terminals into the wiring harness connector as shown above.

 

17. Ground at the indicated position.

 

18.Connect the power harness to the indicated signal plug and its socket.

 

19. The fuse slot for power supply is indicated above.

 

20. Plug the fuse tap into the fuse box, pay attention to the direction of wire.

 

21. Remove the indicated cable clip and place the ECU at its hole.

 

22. Secure the ECU.

 

23. Insert the strut wiring harnesses①②, lock signal harness ③, and power harness④ into the ECU in sequence.

 

24. Check all the connectors.

 

25. Press the added tailgate switch to open and close the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

 

26. Reinstall all the trim panels and install the added tailgate switch.

 

4. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button in the driver's area 3 times;
●Press the original tailgate switch button;
●Press the added tailgate switch button.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Instructions for the added tailgate switch
①Closing speed acceleration
Press and hold the added switch button on tailgate until hearing a beep sound. When the tailgate makes a short beep sound again, the close speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

②Opening speed acceleration
Press and hold the added switch button on tailgate until hearing two beep sounds. When the tailgate makes two short beep sounds again, the open speed acceleration is complete. (There are five speed settings. Repeat this step once to increase by one setting.)

③Height setting
Press and hold the added switch button on tailgate until hearing three beep sounds. When the tailgate makes three short beep sounds again, the height setting is complete. Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height.

④Switch between quick/slow press of the unlock button on remote key
Press and hold the added switch button on tailgate until hearing four beep sounds. When the tailgate makes four short beep sounds again, the switch of pressing way is complete.

⑤Switch between pressing the unlock button twice/three times
Press and hold the added switch button on tailgate until hearing five beep sounds. When the tailgate makes a long beep sound, the switch of pressing times is complete.
⑥Braking force increase (Retention force for open)
Press and hold the added switch button on tailgate until hearing six beep sounds. When the tailgate makes two long beep sounds, the braking force increase is complete. (There are five speed settings. Repeat this step once to increase by one setting.)
⑦Restore to factory settings
Press and hold the added switch button on tailgate until hearing seven beep sounds. When the tailgate makes three long beep sounds, the reset is complete.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

Keywords:

2017-2019 Benz GLC,Corepine Smart Electric Tailgate System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW