+
  • 24BenzE-Class.jpg
  • 24BenzE-Class.png
  • 自制奔驰C级锁.jpg
  • EP12撑杆.jpg

2024 Benz E-Class,Corepine Smart Electric Tailgate System Kit


Category:


Get Quote

Share to

 

2. Product list

 

3. Installation method

1. Remove the front left side door sill panel.

 

2. Remove the rear left door sill panel and B-pillar trim panel.

 

3. Remove the tailgate trim panels.

 

4. Remove the trunk trim panels and floor mat.

 

5. Install the right body bracket at the indicated holes and insert the screw with handle into the body from the indicated direction.

 

6.  Thread the two screws out through the holes.

 

7. Install the right body bracket.

 

8. Install the left body bracket.

 

9. Remove the springs on both sides.

 

10. Remove the indicated fasteners on both sides.

 

11. Remove the springs hangers on the left and right hinges.

 

12. Install the right body bracket, thread the bolt assembly through the hole and then secure the bracket with two U-bolts.

 

13. Tighten the all nuts.

 

14. Install the left body bracket, thread the bolt assembly through the hole and then secure the bracket with two U-bolts.

 

 

15. Hang the original springs onto the left and right tailgate brackets.

 

 

16. Install the electric struts, L on the left and R on the right (the first letter of the strut code).The end with wiring harness pointing inward.

 

17. Route the right strut wiring harness to the left side of the trunk along with the original wiring harness to prevent the strut wiring harnesses from being pulled while the struts are working.

 

 

18. Route the left strut wiring harness along with the original wiring harness as indicated to prevent the strut wiring harnesses from being pulled while the struts are working.

 

19. Remove the original latch.

 

20. Connect the plugs of the lock signal harness to the plugs of the power latch.

 

21. Install the power latch and manually adjust the latch to the locked state.

 

22. Connect the plugs of the lock signal harness to the plugs of original tailgate switch.

 

23.Wrap the two emergency wire of the latch separately with electrical tape and hide them under rear left door sill panel.

 

24. Route the lock signal harness along with original wiring harness as indicated.

 

25. Route the power harness as indicated.

 

26. Ground at the left side of the trunk.

 

27. Connect the plugs of the power harness to the indicated CAN signal plug and its socket.

 

28. The fuse box is located at the right side of the trunk and the fuse slot for power supply is indicated.

 

29. Plug the fuse tap into the fuse box and pay attention to the direction.

 

30. Secure the ECU at the indicated position.

 

31. Insert the left and right strut wiring harnesses①②, lock signal harness③, and power harness④ into the ECU in sequence. Tie them along with original wires.

 

32. Check if the power latch and the struts function well.

 

33. Press the added tailgate switch to close the tailgate once, the system completes initialization, and then test each function of the electric tailgate.

 

34. Strick the hole template to the indiccated position and open a hole(pay attention to align with the hole on the tailgate).

 

35. Cut off the ribs from the trim panel.

 

36. Install the added tailgate switch and reinstall all trim panels.

 

4. System initialization method


1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press and hold the tailgate button on the remote key;
●Press and hold the tailgate button at the driver's area;
●Press the original tailgate switch button;
●Press the added tailgate switch button.

3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module
1.Press and hold the switch button until hearing the third short beep sound. 
2.After releasing the button, you will hear three short beeps, indicating that the voice module has entered configuration mode. (For details, see the voice module operation manual)
④Block the voice module
1.Press and hold the switch button until hearing the fourth beep sound. 

2.After releasing the button, you will hear three four beeps indicating that the voice module has been blocked.
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the added tailgate switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep sound and a short beep sound indicating that the switch between quick press and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.

⑧Braking force increase (5 Settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.

Keywords:

2024 Benz E-Class,Corepine Smart Electric Tailgate System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW