Power Running Board
No data

2. Product list

3. Installation method

1. Remove the tailgate trim panel and hinge trim.

2. Remove the trunk trim panels.

3. Remove the left spring and the grommet where the inner spring hook is hooked.

4. Remove the right spring and the grommet where the inner spring hook is hooked.

5. Install the left body bracket and tailgate bracket at the indicated locations.

6. Install the left body bracket.

7. Install the left tailgate bracket.

8. Install the right body bracket and tailgate bracket at the indicated locations.

9. Install the right body bracket.

10. Install the right tailgate bracket.

11. . Install the electric struts, L on the left and R on the right (the first letter of the strut code). The end with wiring harness should point outward.

12. Reinstall the left and right springs.

13. Connect the connectors of the lock signal harness to the original latch.

14. Connect the connectors of the lock signal harness to the outer tailgate switch.

15. Connect the connector of the lock signal harness to the added tailgate switch.

16. Route the lock signal harness to the left side of the trunk along original wires.

17. Route the strut wiring harnesses.

18. Connect to ground at the indicated location.

19. Check if all the connectors are properly connected.

20. Route the power harness as shown(routing only, no connection).

21. Connect to the indicated location for power supply (open the red cover).

22. Connect to the indicated connector for CAN signal.

23. Insert the left and right strut wiring harnesses①②,lock signal harness③,and power harness④ into the ECU in sequence.

24. Secure the ECU at the indicated location on the left side of the trunk.

25. Press the added tailgate switch button to close the tailgate and open it, the system completes initialization. Then, test each function of the electric tailgate.

26. Attach the hole template to the indicated location and open a hole for the added tailgate switch.

27. Reinstall all trim panels and fit the tailgate switch in.
4. System initialization method
1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.
5. Instructions for the electric tailgate
1. Methods to open and close the tailgate:
●Press the tailgate button on the remote key;
●Press the tailgate button in the driver's area;
●Press the original tailgate switch button;
●Press the added tailgate switch button.
2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.
3. Instructions for the added tailgate switch
①Height setting
Press and hold the switch button on the tailgate. Release it after hearing one long beep — the height has been successfully memorized.
Tip: During tailgate operation, pause it, then manually push the tailgate up to the desired height.
②Closing speed-up
Press and hold the switch button on the tailgate. Release it after hearing two short beeps — the closing speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
③Opening speed-up
Press and hold the switch button on the tailgate. Release it after hearing three short beeps — the opening speed-up function has taken effect.
(There are five speed levels. Repeat this step to increase the level by one.)
④Braking force increase (Retention force for open)
Press and hold the switch button on the tailgate. Release it after hearing one long beep and one short beep — the braking force has been increased.
(There are five levels. Repeat this step to increase the level by one.)
⑤Switch reminder sound toggle
Press and hold the switch button on the tailgate. Release it after hearing one long beep and two short beeps — the switch reminder sound toggle has taken effect. (Default is silent. Repeat the setting to cycle through the options.)
⑥Enter the voice wake-up word and command word modification menu
Press and hold the switch button on the tailgate. Release it after hearing one long beep and three short beeps — the voice wake word and command word modification menu entered.
⑦Voice switch power-off toggle between 72 hours and 0.5 hours
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and one short beep — the voice switch power-off toggle between 72 hours and 0.5 hours has taken effect.
⑧ Voice switch ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and two short beeps — the voice switch ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑨Kick sensor ON and OFF
Press and hold the switch button on the tailgate. Release it after hearing two long beeps and three short beeps — the kick sensor ON/OFF toggle has taken effect. (Default is ON. Repeat the setting to cycle through the options.)
⑩Toggle between double and triple tapping
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and one short beep — the toggle between double and triple tapping has taken effect. (Default is triple tapping. Repeat this step to cycle through the options.)
⑪Tap sensor ON and OFF
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and two short beeps — the tap sensor ON/OFF toggle has taken effect. (Default is ON. Repeat this step to cycle through the options.)
⑫Toggle between 2-press and 3-press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing three long beeps and three short beeps — the toggle between 2-press and 3-press has taken effect. (Default is 3-press. Repeat this step to cycle through the options.)
⑬Toggle between quick/slow press of the unlock button on remote key
Press and hold the switch button on the tailgate. Release the switch after hearing four long beeps and one short beep — the toggle between quick press and slow press has taken effect. (Default is quick press. Repeat this step to cycle through the options.)
⑭Restore to factory settings
Press and hold the switch button on the tailgate. Release the switch after hearing five long beeps. The factory reset has taken effect.
6. Meanings of the buzzer sound:
"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
Keywords:
SHOP