+
  • 16LexusRX (1).png
  • 16LexusRX (2).png
  • 自制丰田锁.jpg
  • EP11撑杆.png

2016-2022 Lexus RX,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product List

3. Installation method

1. Remove the steering column trim panel.

 

2. Remove the screws on the left and right sides of the steering wheel.

 

3. Remove the upper and lower trim panels of the steering column.

 

4. Remove the front left side trim panels and door sill panel.

 

5. Remove the rear left side door sill panel and B-pillar trim panel.

 

6. Take out the trunk liner.

 

7. Remove the trim panel on the left side of the trunk to allow wiring harnesses to pass through.

 

8. Remove the tailgate trim panels.

 

9. Remove the screws from the power latch.

 

10. Remove the original latch and install the power latch.

 

11. Connect the connectors of the lock signal harness to the power latch.

 

12. Connect the connectors of the lock signal harness to the original tailgate switch.

 

13. Install the added switch at the tailgate handle.

 

14. Remove the gas struts.

 

15. Replace the body brackets.

 

16. Install the electric struts, L on the left and R on the right (the first letter of the strut code).

 

17. Pass the strut wiring harness through the original square hole and then plug the hole. Both sides are the same.

 

18. Route the strut wiring harnesses.

 

19. Thread the power harness to the tailgate (do not connect plugs before inserting terminals into wiring harness connector).

 

20. Insert the power harness terminals into the wiring harness connector as shown above.

 

21. Route the power harness.

 

22. Ground at the tailgate.

 

23. Connect to the blue signal plug and its socket at the steering column.

 

24. The fuse slot of constant power (fifth in the second row).

 

25. Move the original fuse from the fuse box to the fuse tap and then plug the fuse tap into the fuse box. Pay attention to the direction.

 

26. Insert the strut wiring harnesses ①②,  lock signal harness ③, and power harness④ into the ECU in sequence and mount the ECU onto its bracket.

 

27. Secure the ECU at the indicated hole.

 

28. Initialize the system once, and then test each function of the electric tailgate.

 

29. Reinstall all the trim panels.

 

5. System initialization method


1. Press the added tailgate switch button to make the tailgate close automatically;
2. Press the switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

6. Instructions for the electric tailgate


1. Methods to open and close the tailgate:
●Press the unlock button on the remote key 3 times;
●Press the unlock button in the driver's area 3 times;
●Press the tailgate handle switch button;
●Press the added tailgate switch button.

2. Method to pause the tailgate:
During the operation of the tailgate, press the button with any of the above methods, and the tailgate will be paused. Press again, and the tailgate will move in reverse.

3. Method to memorize the height:
Open the tailgate to the height you want to set, long press the added tailgate switch, and release the switch after  hearing a long "beep ----" . The height memory is complete.
Tip: During the operation of the tailgate, pause the tailgate, and then push the tailgate to the ideal height with your hand.

 

7. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on;
Long sound of "beep": The height memory is complete.

 

Keywords:

2016-2022 Lexus RX,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW