+
  • 18LexusES (1).png
  • 18LexusES (2).png
  • 自制ES锁.png
  • EP22撑杆.png

2018-2022 Lexus ES,Corepine Smart Electric Tailgate Lift System Kit


Category:


Get Quote

Share to

2. Product LIst

3. Installation method

1. Remove the front left side trim panel and door sill panel.

2. Remove the rear left side door sill panel and B-pillar trim panel.

3. Remove the tailgate trim panels.

4. Remove the trunk liner and adjust the position of the spring on the left side of the trunk.

 

 

5. Locate the mounting holes of the left body bracket.

 

6. Fold the handle of the screw into the shape as shown above for easy insertion into the holes.

 

7. Install the left body bracket.

 

8. Locate the mounting holes of the right body bracket.

 

9. Install the right body bracket.

 

10. Install the left tailgate bracket at the left hinge.

 

11. Remove the indicated screw from the right hinge.

 

12. Install the right tailgate bracket at the right hinge.

 

13. Install the electric struts, L on the left and R on the right (the first letter of the strut code), making sure the ends with wiring harnesses are on the car body.

 

14. Use the circle clip to secure the strut; the same on both struts.

 

15. Bend the sheet metal a little inwards towards the side of the trunk to prevent it from rubbing against the strut. Both the left and right sides are the same.

 

16. Bend the sheet metal a little outwards towards the side of the trunk to prevent it from rubbing against the strut.

 

17. Route the strut wiring harnesses along the hinges to the tailgate and tie them along with the original wiring harnesses.

 

18. Remove the original latch and the emergency cable.

 

19. Mount the emergency cable onto the indicated fastener of our power latch (remove the fastener of the emergency cable from the tailgate first).

 

20. Install the power latch and adjust the latch to the locked state by hand to prevent accidental closing during the installation process.

 

21. Connect the connectors of the lock signal harness to the power latch.

 

22. Connect the connectors of the lock signal harness to the original tailgate switch.

 

23. Install the added tailgate switch with the original screws.

 

24. Wrap the two emergency wires with electric tape and hide them under the rear left side trim panel.

 

25. Route the lock signal harness along original wire harness.

 

26. Route the power harness as indicated.

 

27. Route the power harness as indicated.

 

28. Ground at the left side of the trunk.

 

29. Check all the plugs and the emergency cable.

 

30. The fuse box is located beside the pedals and the fuse slot for power supply is indicated above.

 

31. Plug the fuse tap into the fuse box with wire pointing to the left.

 

32. Remove the wire clip from the indicated hole, install the ECU at the hole and secure it with a nut.

 

33. Insert the strut wiring harnesses ①②, lock signal harness ③, and power harness④ into the ECU in sequence.

 

34. Check whether the power latch and the electric struts function well.

 

35 Test each function of the electric tailgate.

 

36. Reinstall all trim panels.

 

37. If the door closing sound is too loud, please remove the spring from the dust seal at the striker to prevent it from touching the electric lock by making the dust seal lose its elasticity.

 

4. System initialization method


1. Press the added tailgate switch button, and the tailgate will close automatically;
2. Press the tailgate switch button outside the tailgate to open the tailgate and it will make a long sound of "beep".
3. The system initialization is complete.

 

5. Instructions for the electric tailgate


●Press and hold the tailgate button on the remote key;
●Press and hold the tailgate button in the driver's area;
●Press the original tailgate switch button (for models with key sensing, the key needs to be near the car);
●Press the added tailgate switch button.

3. Instructions for the added tailgate switch
①Closing speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the first short beep sound
2.After releasing the button, you will hear a short beep, indicating that the closing speed acceleration has taken effect.
3.Repeat this step once to increase by one setting.
②Opening speed acceleration (5 Settings)
1.Press and hold the switch button until hearing the second short beep sound
2. After releasing the button, you will hear two short beeps, indicating that the opening speed acceleration has taken effect.
3. Repeat this step once to increase by one setting.
③Settings of the voice module
1.Press and hold the switch button until hearing the third short beep sound. 
2.After releasing the button, you will hear three short beeps, indicating that the voice module has entered configuration mode. (For details, see the voice module operation manual)
④Block the voice module
1.Press and hold the switch button until hearing the fourth beep sound. 

2.After releasing the button, you will hear three four beeps indicating that the voice module has been blocked.
⑤Height setting
1.Press and hold the switch button until hearing the fifth short beep sound.
2.After releasing the button, you will hear a long beep sound indicating that the height setting has taken effect.
⑥Switch between quick/slow press of the unlock button on remote key
1.Press and hold the added tailgate switch button until hearing the sixth short beep sound.
2.After releasing the button, you will hear a long beep sound and a short beep sound indicating that the switch between quick press and slow press of the unlock button has taken effect.
⑦Switch between pressing the unlock button twice/three times
1.Press and hold the switch button until hearing the seventh short beep sound.
2.After releasing the button, you will hear a long beep sound and two short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.

⑧Braking force increase (5 Settings)
1.Press and hold the switch button until hearing the eighth short beep sound.
2.After releasing the button, you will hear a long beep sound and three short beeps indicating that the switch between pressing the unlock button twice/three times has taken effect.
⑨Restore to factory settings
1.Press and hold the switch button until hearing the ninth short beep sound.
2.After releasing the button, you will hear a long beep sound and four short beeps indicating that the restoration to the factory setting has taken effect.

 

6. Meanings of the buzzer sound:


"Beep" once: Receiving an open/close or pause signal, the tailgate will immediately open/close or pause;
"Beep" twice: The tailgate has been fully opened or closed;
"Beep" three times:The resistance during opening or closing the tailgate is too large, and the intelligent anti-pinch has been turned on.
 

 

Keywords:

2018-2022 Lexus ES,Corepine Smart Electric Tailgate Lift System Kit

Get a Free Quote

*Note: Please be sure to fill in the information accurately and keep the communication open, we will get in touch with you as soon as possible

SUBMIT NOW